Dynaco Stereo 300 / QSA300 Power Amplifier



Description:

Specifications:

Rated 4-channel Power Output: 75 watts continuous average power per channel into 8 ohms (40 watts per channel into 16 ohms) 20-20,000 Hz, at less than 0.25% total harmonic distortion. Distortion reduces at lower power outputs.

Available 4-channel Output Power:

20-20,000 Hz, all channels driven, 0.25% maximum THD:

75 watts continuous average per channel @ 8 ohms;
100 watts continuous average per channel @ 4 ohms;
40 watts continuous average per channel @ 16 ohms.

Stereo Operation Available Output Power:

Low Impedance Mode Connections:

80 watts continuous average per channel @ 8 ohms;
150 watts continuous average per channel @ 4 ohms;
200 watts continuous average per channel @ 2 ohms;*

High Impedance Mode Connections:

80 watts continuous average per channel @ 16 ohms;
150 watts continuous average per channel @ 8 ohms;*

* 5 minutes sustained full power limit without a fan.

Power at Clipping, 1 of 4 channels, 2500 Hz, less than 1% distortion:

90 watts @ 8 ohms;
130 watts @ 4 ohms;
45 watts @ 16 ohms.

Power at Clipping, Each Stereo channel, 2500 Hz, less than 1% distortion:

Low-Z mode:

95 watts @ 8 ohms;
160 watts @ 4 ohms;
240 watts @ 2 ohms.

High-Z mode:

160 watts @ 8 ohms;
90 watts @ 16 ohms.

Intermodulation Distortion: Less than 0.25% at any power level up to 75 watts rms per channel into 8 ohms with any combination of test frequencies. Distortion reduces at lower power levels.

Half-power bandwidth: 37.5 watts per channel at less than 0.25% total harmonic distortion from 5 Hz to 50 KHz into 8 ohms.

Frequency Response: +0, -1 dB, 10 Hz to 40 KHz @ 1 watt into 8 ohms; ±0.5 dB, 20 Hz - 20 KHz @ 75 watts into 8 ohms.

Hum and Noise: Greater than 95 dB below rated output, full spectrum.

Input: 35,000 ohm load; 1.0 volt for 75 watts into 8 ohms.

Semiconductor Complement: 52 transistors, 40 diodes.

Slewing Rate: 7 volts per microsecond.

Damping Factor:

Greater than 80 to 1 KHz into 8 ohms;
Greater than 50 to 10 KHz into 8 ohms.

Channel Separation: Greater than 70 dB by IHF standards.

Connectors: Inputs: phono jacks. Outputs: Color coded 3-way binding posts with standard 3/4" spacing.

Dimensions: 18-1/4" wide, 14-1/2" deep;, 7" high panel, 17-1/2" wide. Add 1/2" for feet.

Shipping weight: 58 lbs. Net weight: 52 lbs.

Power Consumption: 120 VA quiescent; 10 amps maximum; 50/60 Hz, 120/240 VAC.

Designed by:

Harry Klaus

Year Introduced:

1976

Price:

$269.00 kit
$399.00 assembled

Comments:

Basically two ST-150 units in a single chassis, with separate power supplies. Usable as four independent channels or as a bridged stereo amplifier with 300 watts per channel. The MC2/MC3 meter kits provided output monitoring.



This page created and maintained by Greg Dunn.
Copyright © 2000 Greg Dunn